About Apple next generation iPhone(iPhone 6), there have been
many stories. 5.3 inch and 4.7 inch is said they both are already
around the corner.
When we want to replace cell phone parts, the cell phone repair tools are the first necessaries we should prepare for. How to use
the right repair tools to make a right replacement is a kind of
skill.
One short opening tool pry
One triangle opening picks
One tweezer
One spudger
They can absolutely help you tear donw and install Samsung
galaxy s5 display assembly. Now let’s have a see at how to
replace a lcd display assembly for Samsung galaxy s5.
Insert a fingernail or plastic opening tool into the divot to the left
of the rear-facing camera.
Gently pry and twist the flexible rear cover off the back of the
phone.
Insert a fingernail or plastic opening tool into the recess in the
bottom right corner of the battery and lift upward.
Remove the battery away from the phone.
Using a fingertip, pull the microSD card straight down out of its
slot.
Remove the microSD card from the phone.
Repeat the above procedure to remove the SIM card.
Above processes are finished without any repair tools. So if you
want to replace a back cover or battery for Samsung galaxy s5, it
is easy to make it.
Use a plastic opening tool to pry up the plastic midframe
connector panel.
Remove the connector panel with a pair of tweezers.
Pre: There should be enough adhesive to readhere the panel upon
reassembly, otherwise use a small amount of double-stick tape.
Use the sharp tip of a spudger to pry the home button cable
connector straight up off its socket.
In the following steps you will be using an iOpener to warm the
adhesive affixing the display assembly to the rest of the phone.
This will allow for a safer, easier screen removal. For proper
iOpener use, follow our iOpener heating guide, make sure to pay
attention to all warnings.
Place a heated iOpener on the left side of the phone for at least
90 seconds.
Reheat the iOpener and place it on the right half of the phone.
Following is the important and main process we are talking
about-lcd display assembly teardown.
In the following steps you will be using an opening pick to
separate the adhesive securing the front panel glass. Only pry
where directed. If you experience resistance, stop sliding the
opening pick and reapply heat.
Insert the edge of an opening pick underneath the bottom right
side of the front glass.
Slide the opening pick up along the right side of the display.
Carefully slide the pick around the corner, stopping before the
speaker grille at the top of the phone.
The adhesive securing the top of the phone is only a narrow strip
above the earpiece speaker. Slide the pick along the top of the
speaker to avoid damaging internal components.
Slide the opening pick across the top of the phone, being very
careful not to insert the pick too deeply.
Carefully slide the pick around the upper left corner.
If you encounter any resistance from cooling adhesive, reapply a
heated iOpener to the left side of the phone.
Slide the opening pick down along the left half of the phone
stopping at the lower left corner.
Twist the opening pick to detach the glass from the phone.
If the front panel does not detach easily, it may require
additional adhesive cutting.
Slide the opening pick all the way to the bottom right corner of
the phone, making sure it is securely placed.
In the following step you will be placing an iOpener over the
home button end of the phone, you won’t want your opening pick
to slip out.
Place a reheated iOpener over the bottom portion of the display
assembly.
There are delicate components in this portion of the phone, you
want to ensure the adhesive is warm and easy to loosen to
protect the phone.
The bottom end of the phone contains the soft button and home
button ribbon cables. If you insert the opening pick too far into
the phone you risk cutting these cables.
Slide the very end of the opening pick across the bottom edge of
the display to separate the last of the remaining adhesive.
If the front panel is not easily freed, the adhesive on the soft
button cable may need to be separated.
These cables are thin and easily damaged, therefore be certain
you are only peeling them off the display assembly and not
lacerating them.
Insert an opening pick under the soft button icons on the display
and pry the button cables down off the inside of the front panel.
Slightly lift, but do not remove, the home button end of display
assembly.
Do not remove the front panel entirely. It is still attached by a
connector.
Use the sharp tip of a spudger to lift the front panel assembly
cable connector straight up off its socket on the motherboard.
Safely remove the front panel assembly from phone.
So if you want to fix your LCD digitizer touch screen assembly for Samsung galaxy s5, just use these tools, you can make it.
Attention: all pictures come from iFixit, and the cell phone repair
tools you can also find at hytparts store.
No comments:
Post a Comment